[RESOLVED] Touch panel issue

If you're having trouble with your LattePanda, here's the place to get help.
Forum rules
    Post technical issues here.

    - Discussion tone should be kept polite and focused on facts
    - Vulgar language or flaming constitutes an instant ban
    - Please note we cannot support PM requests for help
    - Members are asked to post in English only so that posts can be well received and properly monitored
    - You can find the RMA guide [here]
    - Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:


    - Have you tried a hard reset?
    - Are you using a 5V@2A+ power supply and a high quality USB cable?
    - Have you tried powering the board through the CN2 headers?
    - Have you tried a cooling solution such as a fan or heatsink?
    - Have you tried reinstalling drivers?
    - Have you tried reloading the operating system?
    - Have you tried flashing the BIOS?
    - Are you able to flash the BIOS at the hardware level?

    If you have not found a solution, post a new issue. To speed up the process please let us know:
    - Have you tried the solutions listed above?
    - What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
    - Have you tried any other solutions?
    - How long have you had your board for?
    - When did you first boot your board?
    - Did it work ok before the issue occurred or has the issue always been there?
    - Use images and videos to help us understand the issue where possible

    If you are seeking RMA:
    - Please open a new topic rather than hijacking someone else's thread
    - Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
    - Completed RMA cases will be marked with [CLOSED]
    You can find the RMA guide [here]

    Resolved Issues
    - If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
    - If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.

    What does troubleshooting support?
    - Hardware queries
    - Hardware issues that weren’t caused by you, e.g DOA board
    - Windows 10 specific issues
    User avatar
    LattePanda
    Site Admin
    Posts: 2626
    Joined: Wed Jan 20, 2016 9:09 am

    Thu Dec 01, 2016 11:56 am

    We are releasing a new set of screens in various sizes.

    I have included links here for the new v1.1 drivers for the touch panels (x86 and x64)
    LattePanda Standard 32-bit (x86)
    LattePanda Enhanced 64-bit (x64)

    These drivers are not backwards compatible so you will need the old v1 drivers if you have an original 7" touch panel. These are included below:
    LattePanda Standard 32-bit (x86)
    LattePanda Enhanced 64-bit (x64)

    Remember to run as administrator
    Enjoy Tinkering with LattePanda ! :lol:

    User avatar
    strawberrymaker
    Posts: 51
    Joined: Sat May 21, 2016 2:26 am

    Tue Dec 06, 2016 11:00 pm

    Any estimates on when we'll see the new displays or get some specs/prices?

    Thanks ;)

    User avatar
    LattePanda
    Site Admin
    Posts: 2626
    Joined: Wed Jan 20, 2016 9:09 am

    Thu Dec 08, 2016 9:37 am

    There have been a few delays - we are still finalizing the samples and expect to push them out for sale january latest, hopefully before. When I know more I will post in this thread.

    Incidentally, ensure you run the included install.bat file as an administrator for it to install properly!
    Enjoy Tinkering with LattePanda ! :lol:

    User avatar
    janwillemp
    Posts: 1
    Joined: Thu Feb 09, 2017 3:31 pm

    Thu Feb 09, 2017 3:45 pm

    Would it be possible to release a driver that works on the alternative I2C slave address? My goal is the connect a 2nd touch panel to the Intel GPIO I2C pins. Just got my gear in so I have no idea if this is realistic at all yet, but it seems like a nice challenge.

    Thanks

    User avatar
    Allen5974
    Posts: 7
    Joined: Sat Feb 18, 2017 1:45 am

    Mon Feb 20, 2017 12:37 am

    how can you tell if you have a new or an old touch panel?

    User avatar
    LattePanda
    Site Admin
    Posts: 2626
    Joined: Wed Jan 20, 2016 9:09 am

    Mon Feb 20, 2017 7:24 am

    Allen5974 wrote:how can you tell if you have a new or an old touch panel?
    look at the date code on the fpc connector - if it is produced after may 2016 it is the new one. if not, it is the old one.
    (e.g. 2016/05/12 = 12th May 2016 is the new version and will need v1.1 drivers)
    Enjoy Tinkering with LattePanda ! :lol:

    User avatar
    strawberrymaker
    Posts: 51
    Joined: Sat May 21, 2016 2:26 am

    Tue Feb 21, 2017 9:05 pm

    Where is it supposed to be on the fpc cable? mine only said "DXG1-0667-070A HX5"

    User avatar
    LattePanda
    Site Admin
    Posts: 2626
    Joined: Wed Jan 20, 2016 9:09 am

    Wed Mar 22, 2017 5:52 am

    from that it is safe to assume you are using the old version. the new ones will have a date code on them.
    Enjoy Tinkering with LattePanda ! :lol:

    User avatar
    TypeLatte
    Posts: 5
    Joined: Sat Feb 25, 2017 6:57 pm

    Fri Mar 24, 2017 1:03 pm

    Hi there,

    Presuming there's still no update on new screen sizes etc?

    User avatar
    LattePanda
    Site Admin
    Posts: 2626
    Joined: Wed Jan 20, 2016 9:09 am

    Thu Mar 30, 2017 3:08 am

    TypeLatte wrote:Hi there,

    Presuming there's still no update on new screen sizes etc?
    We have some 10" samples in the office, unfortunately timescales are non existent right now
    Enjoy Tinkering with LattePanda ! :lol:

    Post Reply