Совсем недавно приобрел LattePanda 4G / 64G.
Один день было все нормально, пока я не попробовал обновить BIOS в связи с установкой Ubuntu.
По чистой случайности записал на Flash не тот образ, в итоге после перезагрузки плата просто умерла, - постоянно мигает красный светодиод.
Пробовал делать Hard Reset, -не помогло, затем с помощью программатора CH341A заливал все прошивки BIOS которые только нашел на репозитории,- результата нет. Прошу помощь, так как у меня на эту плату большие планы.
Плата S70C REV/ 2.0
S70 CR200 CC55F Чип W25Q64FV WINBOND
Recently purchased LattePanda 4G / 64G.
One day everything was fine until I tried to update the BIOS due to the installation of Ubuntu.
By chance, recorded on a Flash is not the way, in the end, after a restart fee just died, constantly flashing red led.
Tried to do Hard Reset, - did not help, then by means of the programmer CH341A filled in all firmwares of BIOS which only found on repository, - there is no result. I ask for help, as I have big plans for this fee.
S70c REV/ 2.0 Board
S70 CR200 CC55F Chip WINBOND W25Q64FV
Помогите разобраться.
Forum rules
- Discussion tone should be kept polite and focused on facts
- Vulgar language or flaming constitutes an instant ban
- Please note we cannot support PM requests for help
- Members are asked to post in English only so that posts can be well received and properly monitored
- You can find the RMA guide [here]
- Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:
- Have you tried a hard reset?
- Are you using a 5V@2A+ power supply and a high quality USB cable?
- Have you tried powering the board through the CN2 headers?
- Have you tried a cooling solution such as a fan or heatsink?
- Have you tried reinstalling drivers?
- Have you tried reloading the operating system?
- Have you tried flashing the BIOS?
- Are you able to flash the BIOS at the hardware level?
If you have not found a solution, post a new issue. To speed up the process please let us know:
- Have you tried the solutions listed above?
- What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
- Have you tried any other solutions?
- How long have you had your board for?
- When did you first boot your board?
- Did it work ok before the issue occurred or has the issue always been there?
- Use images and videos to help us understand the issue where possible
If you are seeking RMA:
- Please open a new topic rather than hijacking someone else's thread
- Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
- Completed RMA cases will be marked with [CLOSED]
You can find the RMA guide [here]
Resolved Issues
- If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
- If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.
What does troubleshooting support?
- Hardware queries
- Hardware issues that weren’t caused by you, e.g DOA board
- Windows 10 specific issues
- Discussion tone should be kept polite and focused on facts
- Vulgar language or flaming constitutes an instant ban
- Please note we cannot support PM requests for help
- Members are asked to post in English only so that posts can be well received and properly monitored
- You can find the RMA guide [here]
- Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:
- Have you tried a hard reset?
- Are you using a 5V@2A+ power supply and a high quality USB cable?
- Have you tried powering the board through the CN2 headers?
- Have you tried a cooling solution such as a fan or heatsink?
- Have you tried reinstalling drivers?
- Have you tried reloading the operating system?
- Have you tried flashing the BIOS?
- Are you able to flash the BIOS at the hardware level?
If you have not found a solution, post a new issue. To speed up the process please let us know:
- Have you tried the solutions listed above?
- What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
- Have you tried any other solutions?
- How long have you had your board for?
- When did you first boot your board?
- Did it work ok before the issue occurred or has the issue always been there?
- Use images and videos to help us understand the issue where possible
If you are seeking RMA:
- Please open a new topic rather than hijacking someone else's thread
- Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
- Completed RMA cases will be marked with [CLOSED]
You can find the RMA guide [here]
Resolved Issues
- If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
- If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.
What does troubleshooting support?
- Hardware queries
- Hardware issues that weren’t caused by you, e.g DOA board
- Windows 10 specific issues
-
LattePanda
- Site Admin
- Posts: 2697
- Joined: Wed Jan 20, 2016 9:09 am
Dear SergeyRus, please check with your purchasing channel to see if they can still provide a replacement for u. I think it should be still a BIOS refreshing issue. Should work if you re-program the BIOS with programmer! Coz it sounds like no hardware issue involved!SergeyRus wrote: ↑Thu Nov 08, 2018 1:06 pmСовсем недавно приобрел LattePanda 4G / 64G.
Один день было все нормально, пока я не попробовал обновить BIOS в связи с установкой Ubuntu.
По чистой случайности записал на Flash не тот образ, в итоге после перезагрузки плата просто умерла, - постоянно мигает красный светодиод.
Пробовал делать Hard Reset, -не помогло, затем с помощью программатора CH341A заливал все прошивки BIOS которые только нашел на репозитории,- результата нет. Прошу помощь, так как у меня на эту плату большие планы.
Плата S70C REV/ 2.0
S70 CR200 CC55F Чип W25Q64FV WINBOND
Recently purchased LattePanda 4G / 64G.
One day everything was fine until I tried to update the BIOS due to the installation of Ubuntu.
By chance, recorded on a Flash is not the way, in the end, after a restart fee just died, constantly flashing red led.
Tried to do Hard Reset, - did not help, then by means of the programmer CH341A filled in all firmwares of BIOS which only found on repository, - there is no result. I ask for help, as I have big plans for this fee.
S70c REV/ 2.0 Board
S70 CR200 CC55F Chip WINBOND W25Q64FV
Enjoy Tinkering with LattePanda ! 