I have a lattepanda alpha and i have both the 7in and 10.1in. When I plug in the LP with either the 7 or 10.1in nothing comes up red light flickers fast then goes normal, then it stays solid like normal boot then i press the power, the blue light just flickers. But when I connect to hdmi it works.
If i could get some help o greatly appreciate it.
Thank you.
Niether ips displays working
Forum rules
- Discussion tone should be kept polite and focused on facts
- Vulgar language or flaming constitutes an instant ban
- Please note we cannot support PM requests for help
- Members are asked to post in English only so that posts can be well received and properly monitored
- You can find the RMA guide [here]
- Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:
- Have you tried a hard reset?
- Are you using a 5V@2A+ power supply and a high quality USB cable?
- Have you tried powering the board through the CN2 headers?
- Have you tried a cooling solution such as a fan or heatsink?
- Have you tried reinstalling drivers?
- Have you tried reloading the operating system?
- Have you tried flashing the BIOS?
- Are you able to flash the BIOS at the hardware level?
If you have not found a solution, post a new issue. To speed up the process please let us know:
- Have you tried the solutions listed above?
- What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
- Have you tried any other solutions?
- How long have you had your board for?
- When did you first boot your board?
- Did it work ok before the issue occurred or has the issue always been there?
- Use images and videos to help us understand the issue where possible
If you are seeking RMA:
- Please open a new topic rather than hijacking someone else's thread
- Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
- Completed RMA cases will be marked with [CLOSED]
You can find the RMA guide [here]
Resolved Issues
- If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
- If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.
What does troubleshooting support?
- Hardware queries
- Hardware issues that weren’t caused by you, e.g DOA board
- Windows 10 specific issues
- Discussion tone should be kept polite and focused on facts
- Vulgar language or flaming constitutes an instant ban
- Please note we cannot support PM requests for help
- Members are asked to post in English only so that posts can be well received and properly monitored
- You can find the RMA guide [here]
- Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:
- Have you tried a hard reset?
- Are you using a 5V@2A+ power supply and a high quality USB cable?
- Have you tried powering the board through the CN2 headers?
- Have you tried a cooling solution such as a fan or heatsink?
- Have you tried reinstalling drivers?
- Have you tried reloading the operating system?
- Have you tried flashing the BIOS?
- Are you able to flash the BIOS at the hardware level?
If you have not found a solution, post a new issue. To speed up the process please let us know:
- Have you tried the solutions listed above?
- What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
- Have you tried any other solutions?
- How long have you had your board for?
- When did you first boot your board?
- Did it work ok before the issue occurred or has the issue always been there?
- Use images and videos to help us understand the issue where possible
If you are seeking RMA:
- Please open a new topic rather than hijacking someone else's thread
- Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
- Completed RMA cases will be marked with [CLOSED]
You can find the RMA guide [here]
Resolved Issues
- If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
- If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.
What does troubleshooting support?
- Hardware queries
- Hardware issues that weren’t caused by you, e.g DOA board
- Windows 10 specific issues
Please provide links on your 7" and 10.1" ips LCD screen. What are you referring to?
If you are talking about the classic LattePanda (i.e., not Alpha) 40-pin LVDS based LCD panel,
then obviously there is a mismatch.
LattePanda Alpha's 30-pin LCD connector is for 30-pin eDP display, not the 40-pin LVDS type.
If you are talking about the classic LattePanda (i.e., not Alpha) 40-pin LVDS based LCD panel,
then obviously there is a mismatch.
LattePanda Alpha's 30-pin LCD connector is for 30-pin eDP display, not the 40-pin LVDS type.
https://www.googleadservices.com/pagead ... gK26PD_BwE
https://www.googleadservices.com/pagead ... gJo4PD_BwE
If these aren't the right screens where can I buy them or get and adapter to make them work.
Great now i have to return them. :/
https://www.googleadservices.com/pagead ... gJo4PD_BwE
If these aren't the right screens where can I buy them or get and adapter to make them work.
Great now i have to return them. :/
Now that LP Alpha is out...
The ips LCD panel seller should update the listing to state that
- it's for LP classic
- not compatible with LP Alpha
This has been the second thread I've seen people encountering the same issue.
The seller should make it absolutely cleat to avoid disappointment.
The ips LCD panel seller should update the listing to state that
- it's for LP classic
- not compatible with LP Alpha
This has been the second thread I've seen people encountering the same issue.
The seller should make it absolutely cleat to avoid disappointment.
-
LattePanda
- Site Admin
- Posts: 2688
- Joined: Wed Jan 20, 2016 9:09 am
Thanks for the tips. We will try to reach out all our distributors to see if they can add some tips on 1st gen accessory product page!ccs_hello wrote: ↑Sun Nov 18, 2018 2:18 pmNow that LP Alpha is out...
The ips LCD panel seller should update the listing to state that
- it's for LP classic
- not compatible with LP Alpha
This has been the second thread I've seen people encountering the same issue.
The seller should make it absolutely cleat to avoid disappointment.
Enjoy Tinkering with LattePanda ! 