Problem with HDMI output using KVM switch

If you're having trouble with your LattePanda, here's the place to get help.
Forum rules
    Post technical issues here.

    - Discussion tone should be kept polite and focused on facts
    - Vulgar language or flaming constitutes an instant ban
    - Please note we cannot support PM requests for help
    - Members are asked to post in English only so that posts can be well received and properly monitored
    - You can find the RMA guide [here]
    - Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:


    - Have you tried a hard reset?
    - Are you using a 5V@2A+ power supply and a high quality USB cable?
    - Have you tried powering the board through the CN2 headers?
    - Have you tried a cooling solution such as a fan or heatsink?
    - Have you tried reinstalling drivers?
    - Have you tried reloading the operating system?
    - Have you tried flashing the BIOS?
    - Are you able to flash the BIOS at the hardware level?

    If you have not found a solution, post a new issue. To speed up the process please let us know:
    - Have you tried the solutions listed above?
    - What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
    - Have you tried any other solutions?
    - How long have you had your board for?
    - When did you first boot your board?
    - Did it work ok before the issue occurred or has the issue always been there?
    - Use images and videos to help us understand the issue where possible

    If you are seeking RMA:
    - Please open a new topic rather than hijacking someone else's thread
    - Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
    - Completed RMA cases will be marked with [CLOSED]
    You can find the RMA guide [here]

    Resolved Issues
    - If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
    - If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.

    What does troubleshooting support?
    - Hardware queries
    - Hardware issues that weren’t caused by you, e.g DOA board
    - Windows 10 specific issues
    Post Reply
    User avatar
    k3dAR
    Posts: 14
    Joined: Tue Jan 07, 2020 5:14 pm

    Sun Jan 26, 2020 9:19 pm

    i have LatePanda V1.2 2GB/32GB with Xubuntu 18.04.3 64bit and KVM Aten CS629

    after KVM switch to second PC, and back, LattePanda not show video on HDMI output, KVM have "keep video active" mode when switched to other,
    but LattePanda switch HDMI output OFF (as i see in xrandr output) while is not active, and not switch back to ON while KVM set back to LattePanda...

    workaround is (not always work) to switch using keyboard to virtual console using CTRL+ALT+F1 and back to Desktop using CTRL+ALT+F7,
    but problem is not about Xubuntu (or GNU/Linux) General, because while LattePanda is OFF and connected to KVM and switch as active, then after PowerOn LattePanda is bios not initializad, wait 5minutes, then connect from LCD Monitor HDMI cable direct (without KVM) and LattePanda show Logo and start initializing and boot system, then is wait to connected HDMI monitor...

    i try many change in BIOS about GPU and PowerSave, reset to default, but nothing help...
    Xubuntu 18.04 64bit @ LattePanda 2GB/4GB S70CR200-CC34E

    User avatar
    k3dAR
    Posts: 14
    Joined: Tue Jan 07, 2020 5:14 pm

    Sun Jan 26, 2020 9:20 pm

    btw: with Raspberry Pi2, Pi3 or ASUS TinkerBoard, TinkerBoardS not have this problem and switch via KVM Video between SBC and Desktop work without problem
    Xubuntu 18.04 64bit @ LattePanda 2GB/4GB S70CR200-CC34E

    User avatar
    k3dAR
    Posts: 14
    Joined: Tue Jan 07, 2020 5:14 pm

    Sun Feb 23, 2020 5:41 pm

    about ~month without answer, thanks "support" :roll: ...

    no more wait, now i go to sollution(i hope) to buy additional 3rd HW Digitus DA-70466 (for 10% of LatePanda board price...) to fix this stup1d LattePanda problem,,,
    Xubuntu 18.04 64bit @ LattePanda 2GB/4GB S70CR200-CC34E

    User avatar
    calpin
    Site Admin
    Posts: 33
    Joined: Fri Apr 15, 2016 9:21 am

    Tue Feb 25, 2020 8:29 am

    Hi, so far as I know, the reason of this problem is the Intel chip will set as low power mode when the HDMI port connect with nothing. so a Display Emulator is a easy way to get around this “function“
    And if you need a software method, we hope this post can help you.
    https://askubuntu.com/questions/453109/ ... plugged-in

    User avatar
    k3dAR
    Posts: 14
    Joined: Tue Jan 07, 2020 5:14 pm

    Tue Feb 25, 2020 4:15 pm

    thanks :-) but:
    - second PC on KVM-Switch with LattePanda is STX+i7100T (=with Intel CPU/GPU) and not have problem

    - DisplayEmulator/Terminator be sure usable for boot without HDMI connected (or KVM switch to LattePanda Not Active), but i need connected HDMI output as LattePanda is primary use as Kodi player

    - using xorg dummy video driver i know and use on servers (without LCD connected for VNC access) many years, but too is not sollution for my problem, because for "bios wait for hdmi" not help and for already started xorg on intel too not solve problem with real hdmi output

    as i write i hope help DisplayEmulator/Through, tomorrow i receive it and make test...

    BTW: before i hoped to some "magic" bios setting combination to disable hdmi "aggresive checking" or "power management"... or change in BIOS update...
    Xubuntu 18.04 64bit @ LattePanda 2GB/4GB S70CR200-CC34E

    User avatar
    k3dAR
    Posts: 14
    Joined: Tue Jan 07, 2020 5:14 pm

    Wed Feb 26, 2020 11:20 pm

    i can confirm - Digitus DA-70466 fixed problem with HDMI limitation of LattePanda on KVM-Switch, now switching work... finally after 2 months i stop twice a day reconnecting LCD-HDMI cable between LattePanda and KVM-Switch :-)
    Xubuntu 18.04 64bit @ LattePanda 2GB/4GB S70CR200-CC34E

    Post Reply