UPS monitoring via LattePanda USB port

If you're having trouble with your LattePanda, here's the place to get help.
Forum rules
    Post technical issues here.

    - Discussion tone should be kept polite and focused on facts
    - Vulgar language or flaming constitutes an instant ban
    - Please note we cannot support PM requests for help
    - Members are asked to post in English only so that posts can be well received and properly monitored
    - You can find the RMA guide [here]
    - Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:


    - Have you tried a hard reset?
    - Are you using a 5V@2A+ power supply and a high quality USB cable?
    - Have you tried powering the board through the CN2 headers?
    - Have you tried a cooling solution such as a fan or heatsink?
    - Have you tried reinstalling drivers?
    - Have you tried reloading the operating system?
    - Have you tried flashing the BIOS?
    - Are you able to flash the BIOS at the hardware level?

    If you have not found a solution, post a new issue. To speed up the process please let us know:
    - Have you tried the solutions listed above?
    - What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
    - Have you tried any other solutions?
    - How long have you had your board for?
    - When did you first boot your board?
    - Did it work ok before the issue occurred or has the issue always been there?
    - Use images and videos to help us understand the issue where possible

    If you are seeking RMA:
    - Please open a new topic rather than hijacking someone else's thread
    - Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
    - Completed RMA cases will be marked with [CLOSED]
    You can find the RMA guide [here]

    Resolved Issues
    - If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
    - If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.

    What does troubleshooting support?
    - Hardware queries
    - Hardware issues that weren’t caused by you, e.g DOA board
    - Windows 10 specific issues
    Post Reply
    User avatar
    pj66300
    Posts: 3
    Joined: Mon Jun 22, 2020 5:14 pm

    Mon Jun 22, 2020 5:41 pm

    I have a 2GB/32GB unit with a Windows 10 Pro licence installed and running. I wish to use the unit to monitor a UPS which is to support a managed 24 port switcher in a relatively inaccessible place (the 19" rack in my loft). The UPS, a PowerWalker VI500 unit , can be monitored by a downloadable application from the manufacturer, titled PowerWalker PoweManager. This application runs on a PC to which the UPS is attached via a cable between the USB ports on the PC and the UPS. This application works fine on a standard desk top PC in that it recognises the UPS and shows the real time operating parameters of the UPS (I tried it). However, when this application is installed on the LattePanda it does not recognise the UPS and therefore does not display the real time data from the UPS. The LattePanda does however recognise the connection to the UPS and beeps. It also appears to register the UPS as if it were a battery running the LattePanda, as if it were a portable PC. The UPS manufacturer cannot understand why the software does not run as expected on the LattePanda and can offer no solution as to the problem. I have tried connecting the UPS to both a USB 2 port and the USB 3 port, but as expected this makes no difference to the end result. There seems to be some difference between the behaviour of the LattePanda USB ports and those on a standard desktop PC. Does anybody have any thoughts as to why this might be so? My intention was to use Tight VNC App to log in to the LattePanda so that I could remotely monitor the UPS. I should say that I had no problem installing and running the App on my desktop and the LP.
    Peter

    User avatar
    ccs_hello
    Posts: 623
    Joined: Sat Oct 13, 2018 9:16 pm

    Wed Jun 24, 2020 6:08 pm

    Please use the proper subform to ask question specific to your classic/v1 board.
    https://www.lattepanda.com/forum-c10

    P.S. hint: compare the device driver and the driver files loaded desktop vs LP-v1

    User avatar
    pj66300
    Posts: 3
    Joined: Mon Jun 22, 2020 5:14 pm

    Thu Jul 02, 2020 5:36 pm

    Apologies. I had not realised the subdivisions. I will not darken the door of the forum again in case I make any further similar errors. I will endeavour to make a comparison of the driver files as you suggest.

    User avatar
    pj66300
    Posts: 3
    Joined: Mon Jun 22, 2020 5:14 pm

    Sun Jul 05, 2020 3:39 pm

    As a consequence of a Windows update in the last few days the USB driver has been updated to the same as that on my desktop, namely 10.0.18362.1. The LP still doesn't see the UPS on its USB port so I don't think this will ever work. I'm afraid the LP is for the junk box along with the Raspberry Pi that also couldn't work with this particular UPS.
    Peter

    Post Reply