Red Light ON and that's it. No Boot

If you're having trouble with your LattePanda, here's the place to get help.
Forum rules
    Post technical issues here.

    - Discussion tone should be kept polite and focused on facts
    - Vulgar language or flaming constitutes an instant ban
    - Please note we cannot support PM requests for help
    - Members are asked to post in English only so that posts can be well received and properly monitored
    - You can find the RMA guide [here]
    - Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:


    - Have you tried a hard reset?
    - Are you using a 5V@2A+ power supply and a high quality USB cable?
    - Have you tried powering the board through the CN2 headers?
    - Have you tried a cooling solution such as a fan or heatsink?
    - Have you tried reinstalling drivers?
    - Have you tried reloading the operating system?
    - Have you tried flashing the BIOS?
    - Are you able to flash the BIOS at the hardware level?

    If you have not found a solution, post a new issue. To speed up the process please let us know:
    - Have you tried the solutions listed above?
    - What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
    - Have you tried any other solutions?
    - How long have you had your board for?
    - When did you first boot your board?
    - Did it work ok before the issue occurred or has the issue always been there?
    - Use images and videos to help us understand the issue where possible

    If you are seeking RMA:
    - Please open a new topic rather than hijacking someone else's thread
    - Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
    - Completed RMA cases will be marked with [CLOSED]
    You can find the RMA guide [here]

    Resolved Issues
    - If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
    - If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.

    What does troubleshooting support?
    - Hardware queries
    - Hardware issues that weren’t caused by you, e.g DOA board
    - Windows 10 specific issues
    User avatar
    corymp
    Posts: 16
    Joined: Thu May 19, 2016 11:07 pm

    Fri Jun 17, 2016 11:03 am

    This just happened to mine after booting the flash drive that updates the bios to on after power loss...

    I'm devastated....

    If the bios is corrupted, is there a tutorial that can be posted how to manually write the new bios to the board over FTDI or using another arduino? Is there another way to program the bios?

    User avatar
    corymp
    Posts: 16
    Joined: Thu May 19, 2016 11:07 pm

    Sun Jun 19, 2016 10:33 pm

    Does anyone have any advice on this? Not liking the new brick I have...


    User avatar
    corymp
    Posts: 16
    Joined: Thu May 19, 2016 11:07 pm

    Mon Jun 20, 2016 9:59 am

    That is what done it.......

    User avatar
    corymp
    Posts: 16
    Joined: Thu May 19, 2016 11:07 pm

    Tue Jun 21, 2016 12:20 pm

    @lattepanda If bios is corrupted, should I still be able to reflash it? My LP was fine untill I flashed the "Auto Power On Bios" at which point I lost at least, video output. Red light is on but no video... Teamviewer was installed and set to always on but I don't see it online and cannot connect so I'm assuming it isn't booting either. Please make a reply at your earliest convenience.

    User avatar
    corymp
    Posts: 16
    Joined: Thu May 19, 2016 11:07 pm

    Fri Jun 24, 2016 1:23 pm

    Is it possible the video is only being output to the IPS display? I never ordered one with my board

    User avatar
    Boring
    Posts: 88
    Joined: Sat Apr 16, 2016 7:14 pm

    Sat Jun 25, 2016 5:28 am

    Does at acquire an IP address? And do you get a response if ping the IP?

    User avatar
    corymp
    Posts: 16
    Joined: Thu May 19, 2016 11:07 pm

    Wed Jun 29, 2016 6:28 pm

    no.... so that answers my question :(

    User avatar
    LattePanda
    Site Admin
    Posts: 2661
    Joined: Wed Jan 20, 2016 9:09 am

    Thu Jun 30, 2016 11:49 am

    corymp wrote:@lattepanda If bios is corrupted, should I still be able to reflash it? My LP was fine untill I flashed the "Auto Power On Bios" at which point I lost at least, video output. Red light is on but no video... Teamviewer was installed and set to always on but I don't see it online and cannot connect so I'm assuming it isn't booting either. Please make a reply at your earliest convenience.
    Hi corymp
    Did you unplug the u-disk before auto-writing or just start?
    try contact us by email techsupport@lattepanda.com ,we will provide you RMA
    Enjoy Tinkering with LattePanda ! :lol:

    User avatar
    maideii
    Posts: 12
    Joined: Tue May 24, 2016 3:15 am

    Fri Jul 01, 2016 1:20 am

    @Lattepanda

    Me also in the same end result but in different condition. I had successfully flashed the board with default bios file as shown in the tutorial in your github. After reboot, it just went black and red light continuous on without blinking. USB drive also no blinking. Is there anyway i can force reflash the bios?

    Post Reply