Code 10 wifi issue (one or more network protocols missing?)

If you're having trouble with your LattePanda, here's the place to get help.
Forum rules
    Post technical issues here.

    - Discussion tone should be kept polite and focused on facts
    - Vulgar language or flaming constitutes an instant ban
    - Please note we cannot support PM requests for help
    - Members are asked to post in English only so that posts can be well received and properly monitored
    - You can find the RMA guide [here]
    - Please check if your question has already been answered before opening a new thread. If it has not, please verify the following:


    - Have you tried a hard reset?
    - Are you using a 5V@2A+ power supply and a high quality USB cable?
    - Have you tried powering the board through the CN2 headers?
    - Have you tried a cooling solution such as a fan or heatsink?
    - Have you tried reinstalling drivers?
    - Have you tried reloading the operating system?
    - Have you tried flashing the BIOS?
    - Are you able to flash the BIOS at the hardware level?

    If you have not found a solution, post a new issue. To speed up the process please let us know:
    - Have you tried the solutions listed above?
    - What board are you using? Standard (2GB RAM/32GB eMMC) or Enhanced (4GB RAM/64GB eMMC)?
    - Have you tried any other solutions?
    - How long have you had your board for?
    - When did you first boot your board?
    - Did it work ok before the issue occurred or has the issue always been there?
    - Use images and videos to help us understand the issue where possible

    If you are seeking RMA:
    - Please open a new topic rather than hijacking someone else's thread
    - Mark RMA posts with [DEFECTIVE] + <helpful description of issue>. We can then approve/disapprove each request
    - Completed RMA cases will be marked with [CLOSED]
    You can find the RMA guide [here]

    Resolved Issues
    - If you manage to fix an issue, please share your solution for the good of the community. It could help someone else in future.
    - If an issue is resolved the thread should be marked as [RESOLVED]. We can then sticky the thread to help people in future.

    What does troubleshooting support?
    - Hardware queries
    - Hardware issues that weren’t caused by you, e.g DOA board
    - Windows 10 specific issues
    Post Reply
    User avatar
    sophocha
    Posts: 10
    Joined: Thu Dec 29, 2016 11:34 am

    Fri Dec 30, 2016 11:59 pm

    Here is my story so far.....it is a frustrating one!

    1) purchased an enhance version
    2) connected it on an asus 5v/2a charger, system couldn't boot up...just stayed on a blank screen after the lattepanda logo
    3) Tried to load win pro 10, was stuck on "getting devices ready" and system was shutting down.
    4) Made a custom charger (5v/2.5a) and connected it on CN2....that made the system stable
    5) Loaded Win 10 pro and drivers.....boom....code 10 on wifi, couldn't connect to the internet.
    6) Reloaded BIOS and loaded the official image from the website, all was good!!!.......for couple of hours only!.....then code 10 again on the wifi plus bluetooth problems (devices were connected but nothing worked!)
    7) Reloaded the official image again.....everything was working fine for couple of hours and then all the sudden code 10 again !!!
    8) Tried to troubleshoot to see what produces this code 10 error....windows said "one or more network protocols missing"...must be a software corruption in the registry ........HELP
    9) This product fascinates me but at the same time disappoints me so much.....

    EDIT: This seems to work without doing a complete fresh installation
    1) open an admin cmd......I'm not sure which command did the trick ( I googled "one or more network protocols missing") but I'm writing all of them:

    2) type as an admin:
    netsh int ip reset
    netcfg -d
    netsh int ipv4 install
    netsh winsock reset

    3) Open up device manager and uninstall the broadcom driver
    4) restart
    5) install the broadcom driver from the official lattepanda driver pack....yellow exclamation mark on device manager goes away! NO CODE 10 !!! (so far a whole day of surfing the internet) but I do not know how long it will last, lets hope forever.

    User avatar
    LattePanda
    Site Admin
    Posts: 2661
    Joined: Wed Jan 20, 2016 9:09 am

    Thu Jan 05, 2017 11:27 am

    Wish you luck. And normally, we suggest you don't update the driver for it. If you did ,you can try uninstall it with check the "delete the driver file".And you can find the whole LP driver above ,in the Forum rules :)
    Enjoy Tinkering with LattePanda ! :lol:

    User avatar
    sophocha
    Posts: 10
    Joined: Thu Dec 29, 2016 11:34 am

    Fri Jan 06, 2017 6:21 am

    Problem is back! Windows has updated to anniversary edition (1067). I don't get a code 10 in device manager.Only an exclamation mark on the wifi icon saying 'no internet'. I don't have to uninstall the driver though. A simple restart fixes the problem now.
    LattePanda wrote:Wish you luck. And normally, we suggest you don't update the driver for it. If you did ,you can try uninstall it with check the "delete the driver file".And you can find the whole LP driver above ,in the Forum rules :)
    EDIT: I have downgraded the driver. Apparently the driver that I had was 102.19.I have downgraded to 102.10 and everything is fine now!

    User avatar
    LattePanda
    Site Admin
    Posts: 2661
    Joined: Wed Jan 20, 2016 9:09 am

    Mon Feb 13, 2017 10:40 am

    thanks for sharing your solution!
    Enjoy Tinkering with LattePanda ! :lol:

    User avatar
    sophocha
    Posts: 10
    Joined: Thu Dec 29, 2016 11:34 am

    Mon Dec 10, 2018 9:00 pm

    Update after a year of frustration on Code 10. i HAVE FOUND THE SOLUTION!!! (tested on Windows 10 LTSB).

    1) install the driver
    2) copy the .txt file in system32
    3) refresh and done!

    https://openload.co/f/UBLrQJbuN-Q/tryin ... roblem.rar

    Post Reply