Here I will share my Titan case assembly process with you guys.
What you received: LattePanda Alpha/Delta Board and Titan Case.
1.First, remove the two wings of the upper half of Titan case.
(Tip: It would be easier to disassemble them by pulling away from the middle of the wings)
2.Then put your LattePanda Alpha/Delta into Titan case.
(Tip 1: It could be easier if you put the side with audio jack into the case first.
Tip 2: In this step, you can install the antenna, SSD, eDP and Touch connectors before closing the lower half of Titan case, and the rest parts,such as SD card, Ethernet cable and USB ports, should be connected after installation.)
3.After the upper and lower half of Titan case are installed, screw the four corners.
4. Then buckle the wings and complete the installation:
5. After installation, the ports of each side are as follows:
[Tutorial] of Titan Case Assembly
- LattePanda
- Site Admin
- Posts: 2707
- Joined: Wed Jan 20, 2016 9:09 am
@Queenie, thanks for your sharing about the Titan case assembly! ;)
Share history version photos of Titan case for LattePanda Alpha edition products here!
Share history version photos of Titan case for LattePanda Alpha edition products here!
Enjoy Tinkering with LattePanda ! 

- LattePanda
- Site Admin
- Posts: 2707
- Joined: Wed Jan 20, 2016 9:09 am
Yes. Please keey an eye on DFRobot.com. Now we are still working on the last batch like 30 packages delivery for our backers from IGG and KS. After that, we will organize to launch the Titan case to our distribution channels.
Enjoy Tinkering with LattePanda ! 

Queenie wrote: ↑Fri Jan 11, 2019 10:46 amHere I will share my Titan case assembly process with you guys.
What you received: LattePanda Alpha/Delta Board and Titan Case.
修正2.jpg
1.First, remove the two wings of the upper half of Titan case.
(Tip: It would be easier to disassemble them by pulling away from the middle of the wings)
修正1.jpg
2.Then put your LattePanda Alpha/Delta into Titan case.
(Tip 1: It could be easier if you put the side with audio jack into the case first.
Tip 2: In this step, you can install the antenna, SSD, eDP and Touch connectors before closing the lower half of Titan case, and the rest parts,such as SD card, Ethernet cable and USB ports, should be connected after installation.)
修正4.jpg
3.After the upper and lower half of Titan case are installed, screw the four corners.
修正5_副本.jpg
4. Then buckle the wings and complete the installation:
修正6.jpg
5. After installation, the ports of each side are as follows:
细节图1.jpg
细节图3.jpg
细节图2.jpg
细节图4.jpg
M.2 SSD or NVME Passive Cooler
Is there enough space underneath the case (for passive cooler)?
Sample ;
https://tr.aliexpress.com/item/40000216 ... d379498e-4
- LattePanda
- Site Admin
- Posts: 2707
- Joined: Wed Jan 20, 2016 9:09 am
@ender, Titan case is designed with space reserved for M.2 SSD, but not enough space for an SSD passive cooler.
Enjoy Tinkering with LattePanda ! 

Hey looking at this case and have a few questions I was wanting to make a hackintosh and get the Bluetooth/ wifi card and adapter. Obviously this won’t fit in the case is it possible to mount just the lid to the board and then stick some stand offs or something to raise it up off the table/surface?
I was also looking at these: https://www.amazon.com/CHAOHANG-RP-SMA- ... A2W45BBQTM
Is there room somewhere on the side of the lid to mount them for better signal? Or will the antennas the bord comes with work fine without the bottom of the case?
I was also looking at these: https://www.amazon.com/CHAOHANG-RP-SMA- ... A2W45BBQTM
Is there room somewhere on the side of the lid to mount them for better signal? Or will the antennas the bord comes with work fine without the bottom of the case?
- LattePanda
- Site Admin
- Posts: 2707
- Joined: Wed Jan 20, 2016 9:09 am
Hi kasek, you can't just install the lid to the board, because the 4 screw holes are on the bottom of the case.
How do you want to install your antennas? Generally the original wifi antennas are enough for personal projects.
How do you want to install your antennas? Generally the original wifi antennas are enough for personal projects.
Enjoy Tinkering with LattePanda ! 
